CHINA Mobile Phones Secret Codes

Default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Factory mode: *#987#
LCD contrast: *#369#
Restore factory settings: *#987*99#
Software version: *#800#
Software version: *#900#
Set default language: *#0000# Send
Set English language: *#0044# Send
Set English language (new firmware): *#001# Send

Service codes Fly:
2040(i) reset defaults: *#987*99# Send
M100 software version: ####0000#
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#

<>

Hyundai hwp-110 Nam Programming :
Nam Set: #86904**89397#
DM Mode: ##2740*
(Open phone, inter code, close phone)

Hyundai hgc-120, 130, 200 Nam Programming :
Nam Set: #86904**89397#

Hyundai hgc-310, 600, 610 Nam Programming :
Nam Set: ##20022002, end, 1, Spc Code
Field Test: ##20022002, end, 1, Master Code

Hyundai Curitel h100, 150, hx510b, 520, etc Nam Programming :
Nam Set: ##20022002, end, 1, Spc Code
Field Test: ##20022002, end, 1, Master Code
A-key: 2539**
Debug Menu: ##27732726, end
Sar Test: ##27752345, end
Baud Rate: ##36**, end
DM mode enable: **1004, end
DS mode enable: **1005, end
Test Bell/Voice/Led/Dot: ##1122, end
RF Mode: ##2240, end
Ras Ram: ##2774, end
Cmux1: **0481, end
Cmux2: **0482, end
RX Mode Fax: **0492, end
RX Mode Data: **0491, end
RX Mode Reset: **0490, end

CDMA Secert Codes <>

Sony CM-M1300, 3300, Z200 Nam Programming :
Nam Set: 111111+Ok(Jog Dial)+Select+Programming+Ok+Spc

CDMA Secert Codes <>

Lg LX,VX-series, VX4400, VX6000, etc Nam Programming :
Nam Set: ##Spc(#)
Nam Set: Menu, 0
Advanced Settings: ##2342(#)
Vocoder: ##8626337,ok(#)
CAI Change: ##7738,ok(#)
Enable TTY: ##889,ok(#)
A-key: ##2539,ok(#)
Reset (Life time, Clear Memory, etc): ##786,ok(#)

lgc-300, etc Nam Programming :
Nam Set: Menu, 9, Spc
A-key: Press "Sto" 3sec, 2539**

lgc-330w, etc Nam Programming :
Nam Set: Menu, 4, 0, Spc
A-key: 2539**

lgc-510, v111, etc Nam Programming :
Nam Set: Menu, 3, 0, Spc
A-key: 2539**

lgc-500, 800w, etc Nam Programming :
Nam Set: Menu, 9 , 0, Spc
Debug Mode: Menu, 7, 0, Fsc
Debug Mode: Menu, 8, 0, Fsc
A-key: 2539**

<>

SonyEricsson T608, etc Nam Programming :
Nam Set: 923885, joystick >, 111111
Nam Set shot: 987, joystick >, 111111
Nam Set long: 222652, joystick >, 111111
Vocoder: ##8626337, joystick >, 111111
Debug screen: ##33284, joystick >
Life Timer: ##786, joystick >
SW ver: 9#4#3#, joystick >
Edit Profile: ##3282, joystick >
Service menu: *#06*

Ericsson A1228c, T61, etc Nam Programming :
Short NAM: 987+Menu
Long NAM: 923885+Menu+Spc
CDMA Mode: 904093+Menu
Analog Mode: 904095+Menu
QNC: 904097+Menu
Debug Screen: 904090+Menu
DM Mode: 904050+Menu

CDMA Secert Codes <>

Nokia 3280, 3285, 3580, 3585, 5185, 6185, 8280, etc Nam Programming :
Nam Set: *3001#12345#
Software Version: *#837#
Software Version: *#9999#
Esn Number: *#92772689#
Restart Phone: *#75681#
Restart Phone: *#75682#

Nokia 8887 Nam Programming :
Nam Set: *3001#12345#
Version: *#0000#
Evrc: *#8378#
Esn/Data/Timer: *#92772689#
SID: *#743#

Nokia 8587 Nam Programming :
Nam Set: *#626#7764726#
A-Key: #8159357022#4579# (26 digits)
A-Key: #8159357022#4547# (20 digits)
Version: *#0000#
Version: *#837#
Vocoder: *#3872#
Change language: Menu 5, 3, 1
Change DM mode: *#7678#
Debug Screen: *#8378#
Debug: *#8380#
Field Test Menu: *#83788#

SPC Unlock, Factory Reset :
Full Factory Reset: *#7370#
Resets all settings including non-user changeable items (like SPC)


NOKIA TEST MODE:

51xx, 61xx, 71xx, 3285, 63xx, etc :
1) Turn on the phone. Press *3001#12345#
2) Scroll up to where it says "Field Test" and choose SELECT
3) Highlight "Enable" and choose OK. Turn the phone off then back on.
4) If the test mode screen does not show up press MENU and scroll
down to "Field Test" choose SELECT. Press 0 1 then choose OK.
5) Lower left or upper left number is the signal strength.
6) To turn off the test mode press MENU and scroll down to where it says
"Field Test" choose SELECT. Press 0 0 and then choose OK.

3360, 6360, etc :
1) Turn on the phone. Press *3001#12345#
2) Scroll up to where it says "Field Test" and choose SELECT
3) Highlight "Enable" and choose OK. Turn the phone off then back on.
4) If the test mode screen does not show up press MENU and scroll
down to "Field Test" choose SELECT. Press 2 1 0 1 then choose OK.
5) Lower left or upper left number is the signal strength.
6) To turn off the test mode press MENU and scroll down to where it says
"Field Test" choose SELECT. Press 2 1 0 0 and then choose OK.

CDMA Secert Codes <>

Motorola 7760, 7860, 2260, 8160, etc Nam Programming :
Nam Set: Fcn,0000000000000, Rcl
Nam Set: 74663#, Fcn, Fcn
Test Mode: Fcn, 00**83786633, Sto

Motorola v60c, v120c etc Nam Programming :
Nam Set: 74663#, Menu, Menu, Spc
Nam Set: Menu, 073887, * (type quickly)
Test Mode: Menu, 073887*, Spc
Debug Mode: ##33284

Force the phone into DIGITAL ONLY mode:
1) ##33284 (Debug)
2) RIGHT Softkey (Next) Twice
3) Down arrow 10 times to "PrefMod"
4) RIGHT Softkey (Change) until you see "DigOnly"
5) LEFT softkey (Exit)
6) MENU then LEFT Softkey return to idle screen
7) ##33284 (The last 4 will not display if you have done it correctly)

Motorola Razr V3C Nam Programming:
Nam Set: 74663 # clr clr
Nam Set: #073887* , then SPC

Motorola Q Nam Programming:
Nam Set: [Send] + 074663 + [Send] + [Send], Selecct NAM#

Motorola t182, c210, etc Nam Programming :
Nam Set: ##298645665, end
Short Nam: ##073887, sto
Debug Menu: ##1111, end
Service Menu: ##2222, end
Sound NS/EC on/off switch: ##1113, end

Motorola v710, v730, v740, ms150, etc Nam Programming :
Nam Set: 8378*# + press 3 times NATE (spc - 071082)
Test Mode: Menu, 073887*, Spc
Service Menu: #758353266#646#

Motorola StarTac 2004 Nam Programming :
Nam Set: 5759789*#, press "Rec" button 3 times, (spc - 915037)

Motorola ms200, ms400, ms800, etc Nam Programming :
Nam Set: 5759789*#, press "Camera" button 3 times, (spc - 915037)
Nam Set: 246791538*#, press "Camera" button 3 times, (spc - 915037)

Motorola v6060 Nam Programming :
Nam Set:147*369#456*0#


MOTOROLA TEST MODE :

v60, c120, c331, etc:
1) Turn on the phone. Press MENU 0 7 3 8 8 7 *
2) The phone will require you to "Enter a Security Code", press 000000, OK
3) Scroll down to "Test mode" choose SELECT. Scroll down to "Enable"
choose SELECT. Your phone is now in test mode.
4) Signal strength is the 3_rd number down on the left hand side of the screen.
5) To toggle between regular mode and test mode: Press MODE then
quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.
6) To turn off the test mode the phone must be in regular mode, then follow
the above sequence and scroll down to where it says "DISABLE" instead of
"ENABLE" and choose select.

CDMA Secert Codes <>

Sanyo 4900, 5150, 5300, 8100, etc Nam Programming :
Nam Set: ##Spc+Ok+Key Down+Ok
Advanced Setup: ##3282+Ok+Key Down+Ok+Msl
A-key: ##2539+Ok+Key Down+Ok
Version: ##**837+Ok+Key Down+Ok
Debug Menu: ##FSC+Ok+Key Down+Ok
Airtime menu: ##8463+Ok+Key Down+Ok
Change CAI: ##7738+Ok+Key Down+Ok
Vocoder: ##8626337+Ok+Key Down+Ok
Reverse Logistic: ##786+Ok+Key Down+Ok
Set IP Address: ##2769737+Ok+Key Down+Ok
TTY On/Off: ##889+Ok+Key Down+Ok
Ready Link: ##4636+Ok+Key Down+Ok
Browser Init On/Off: ##4682+Ok+Key Down+Ok
Picture Token: ##25327+Ok+Key Down+Ok
Unknown Code: ##5282277+Ok+Key Down+Ok
(SPC=000000, FSC=040793)

Sanyo scp-A011, smp-A017, etc Nam Programming :
Nam Set: F9(3 beep) + 0*72696#767

<>

Audiovox 4000, 9000, 9100, 9155, 9500, etc Nam Programming :
Power the phone ON and wait until the little light on top goes out, then press:
Nam Set: 289,Fcn, #,1
Service menu: Fcn,0,0, FSC

Power the phone ON and press:
Test Mode: Hold (2,*,Rcl) + Power

Test Mode Commands:
99 - download - flash phone
124 - inam data write
125 - version
126 - get ESN
127 - get SPC
128 - get User lock
129 - is WFTV data write
137 - get FSC code
138 - NPcode (nam program code)
139 - dscode
141 - restart
218 - Read_Addr
000 - is cdma mode
001 - is fm mode
002 - is pcs mode
008 - is reg read addr
020 - is lna_range

Audiovox (Hyundai) cdm-100, 130, 135, 8300, 8500, 8600, 8910, etc Nam Programming :
Nam Set: ##20022002, end
Read user lock: #5625*, end
Port settings: ##7678, end
DM baud rate: ##2283, end
DM mode enable: **1004, end
DS mode enable: **1005, end
Misc. Test: ##27752345, end
S/W Test1: ##27732726, end
S/W Test2: ##2240, end
Debug screen: ##2773, end
Clear MRU: ##6782, end
Rfnu_Contents: ##2250, end
?????: ##1133, end
?????: ##1144, end
P_Rev: ##7738, end
GPS Test: ##4771, end
A-Key: 2538**
SMS Eng: ##767364, end
Battery_adc: ##2768, end
Tests: ##1122, end

Audiovox 8610, 8910, etc Nam programming :
Name Set: ##847446, end, 111111

Audiovox pcx-3500xl Nam Programming :
Nam Set: ##2726+Send+1998+1+Spc+1

Audiovox-107 Nam Programming :
Nam Set: 45680*47*869#1

Audiovox CMP-3 Nam Programming :
Nam Set: 45680*47*869#1
Dm Mode: Menu, 6, 6

Audiovox 9950 Nam Programming :
Nam Set: ##3282

Audiovox Z800 (Audiovox 7900, Sharp) Nam Programming :
Nam Set: m + # + envelope key + * + 1

Audiovox Thera (Toshiba 2032) Nam Programming :
Thera Nam Programming User Manual - nam_thera.pdf

Audiovox (UTStarcom) PPC 6600, 6700, etc Nam Programming :
Nam Set: ##SPC + Send
Nam Set: #*#SPC + Send
Nam Set: ##SPC#
DM mode: ##3424 + Send
DM mode: #*#3424 + Send
DM mode: ##3424#
Programming User Manual - programming_instructions.pdf

CDMA Secert Codes <>

Kyocera 2345, 3035, 5135, 6035, Se47, KX, KE - series, etc Nam Programming :
Nam Set: 111111+Jog Dial(Ok)
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Life Timer: ##786,ok
A-key: ##2539,ok

Tips:
On some kyocera handsets the factory service module has not been disabled
and the phone can be programmed without the Spc by inputting:
Nam Set: ##333333 menu (service)

Qualcomm qcp-800 Nam Pogramming :
Nam Set: Menu+3+0+Spc
Field Test: Menu+7+0+Fsc

CDMA Secert Codes <>

Samsung sph-n240, n400, a460, a500, etc Nam Programming :
Nam Set: ##Spc
Test Mode: 47*869#1235
Debug Menu: ##33284,ok
Service Menu: Menu+8+0 (#889)
Reset (Life time, Clear Memory, etc): ##786,ok
A-key: ##2539,ok
Label Selection: ##3882,ok
Label(Home, Work, etc) : **523,ok
NGG Setting (Gateway, etc.): ##2769737,ok
Vocoder: ##8626337,ok
CAI Change: ##7738,ok
Enable TTY: ##889,ok

Samsung a530, a610, a620, a660, a670, etc Nam Programming :
Nam Set: Menu, 6, *
Nam Set: ##3238, ok
Nam Set: ##SPC (##000000), ok
Service Menu: Menu, 9, *
Test Mode: 47*68#13580
Test Mode: 47*869#1235

Samsung X, E, V, S-series (korean models), e250, v420, s350, etc Nam Programming :
Nam Set: 6548#0**4#6
Nam Set: 47*869#08#9 --Activate Chachu Samsung S-106
Nam Set: 74153697193
Test Mode: 5809540*45680 (88 - EFS reset)
Debug Menu: Menu(hold 2sec)+0, 6725 or 9720 or 1973 or 0415
Debug Menu: Menu+0(hold 2sec), 6725 or 9720 or 1973 or 0415
Debug Menu: Home(top of keypad)+0, 6725 or 9720 or 1973 or 0415

Samsung sch-411, 611, n105, a100, a300, a2000, etc Nam Programming :
Nam Set: 47*869#08#9
Nam Set: Menu+60
Test Mode: *759#813580
Test Mode: 5809540*45680
A-key: Menu+0, 25##
External Audio: Menu+0, ####
Debug Menu: Menu+8, 0415 or Spc
Debug Menu: Menu+9, 0415 or Spc
Brief NAM Programing: Menu+40,626 (not all version)
LCD Contrast: Menu+45 (not all version)
SIO Mode: Menu+49
SIO Mode: Menu+69

Samsung N356 (India version) Nam Programming :
Test Mode: Menu, 5, down arrow, *
Test Mode: **00## (in some flashes)

Samsung i700, etc Nam Programming :
Nam Set: Go to start and select "PHONE" from the drop down menu, dial #83587

Samsung i300, etc Nam Programming :
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. Enter OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice